Making Old Tile Grout New Again
Ceramic tiles are great, but aging grout can take away from the tiles’ good looks. Fortunately, fixing up your grout problems are an easy fix. Here are some tips for making your ceramic tiles look like new.
Ceramic tile will probably always maintain its place as one of the very best indoor flooring surfaces on the planet, but even a ceramic floor doesn’t always retain its good looks. And when problems do arise, it usually has to do with grout. But deteriorating tile grout is definitely something you can fix up yourself. All you need is the kind of basic information that you’ll find here.
Before you get busy ripping out old grout and putting in some new stuff, there are a few things you need to understand:
- Is an ugly grout colour the problem with your floor? Light shades of grout lines can be darkened easily with paint-on grout dye.
- Are you plagued by crumbling grout? This is easy to fix, as you’ll see.
- Cracked grout may be a different issue because this kind of failure probably goes beyond poor grout itself. It could be that slight movement of the tile on an inadequate subfloor or wall is the cause. And if this is the case, then the new grout might crack eventually, too. That said, re-grouting is still the best way to go, at least until you’re ready to replace the tile.
Removing Failing, Old Grout
- Your first step is to remove the failing old grout, and this may be easy or difficult depending on what you’ve got.
- Any hardware store can sell you a claw-shaped, carbide-tipped hand tool designed for scraping out old grout, and this is practical on small areas with loose grout.
- If this hand tool proves too slow or tiring, there are power tools designed to do the job. And the best I know is called the Multimaster. It’s made by a European company called Fein, and is designed for sanding, polishing, and cutting. It also is made to take an abrasive attachment especially designed for grout removal.
- In practice you’ll find that a combination of power and hand tools does the best job removing old grout.
- As you work, aim to remove enough grout so there’s at least 3 to 4 mm of depth to accept new grout. While it’s possible to apply grout into gaps that are shallower than this, deeper is better because it boosts your chances that the new grout will stay put.
Vacuum, Vacuum… Then Vacuum Again
- When you think you’ve got all the old grout removed, vacuum the area thoroughly to remove dust and grit, then take a closer look.
- You’re bound to have missed a spot or two, and now’s the time to remove any old grout that you missed. Vacuum again.
- Cleanliness is key to the adhesion of new grout, so don’t attempt to use just a broom.
Applying New Grout
- Ceramic tile grout always comes as a powder that you mix with water. Start by mixing a batch of grout to the consistency of peanut butter. You can do this by hand with a trowel, but you’ll get smoother results more quickly using a mixing paddle spun in a hand-held drill.
- Use a wooden or rubber-edged trowel to spread grout over the tiles and into the grout gaps in a 10 or 20 square foot area of floor. Make sure all gaps are filled, with excess grout scraped off the surface. What you’ll have at this stage is a dirty looking floor, but one that’s almost done.
- Wait for five minutes and gently wipe the tiles over a grout joint with a damp sponge. What you’re looking for is grout that’s partially hard, but still soft enough to be wiped cleanly off the tiles. If more than a tiny bit of the grout comes out, wait a while longer and try again.
- When the grout is firm enough to clean properly, wipe and rinse your sponge often as you work. It may take six or eight passes before the tiles are completely clean.
- Leave the area alone for a day or two, and then open it up to full traffic. You’ll be amazed how much new grout can improve the look of your home.
If you enjoyed this article, be sure to sign up for our weekly home and garden newsletter. You’ll get the our latest articles on creating a beautiful home delivered right to your inbox.